实验室用喷雾干燥机,实验室喷雾干燥机
产品型号:Jipad-2000ML
简介:

实验室喷雾干燥机将排风管连接好并**有红色高温标志的不锈钢出风口感测的上沿,并保证排风管的尾部对着通气良好的地方,以防尾气对实验人员造成伤害.

详细介绍
Jipad-2000ML小型喷雾干燥机,喷雾干燥机,实验室用喷雾干燥机,实验室喷雾干燥机
尊敬的客户,我们是厂家直销,具体价格要电议的,谢谢您!上海旌派祝您生活愉快。
Jipad-2000ML小型喷雾干燥机安装说明:

1.将设备放置在一靠近通风位置良好的位置,并固定底部轮彀;
2.将白色聚四氟垫片放置在玻璃干燥塔的上沿,然后将玻璃干燥塔连同垫片顶在黑色法兰盘上并放正,*后用黑色大卡箍夹紧;
3.将旋风分离器顶进有红色高温标志的不锈钢出风感测处,并摆正,然后用中型卡箍将旋风分离器和干燥塔连接;(不锈钢感测可以左右移动调节,方便旋风分离器和干燥塔更好的连接)
4.Jipad-2000ML喷雾干燥用小型卡箍将冷阱和玻璃干燥塔连接、卡紧;
5.用小型卡箍将收集瓶和旋风分离器连接、卡紧;
6.以上装配前需要将玻璃干燥塔、旋风分离器、冷阱、收集瓶洗净并烘干;
7.将排风管连接好并**有红色高温标志的不锈钢出风口感测的上沿,并保证排风管的尾部对着通气良好的地方,以防尾气对实验人员造成伤害;
8.将喷头清洗干净,并烘干保证喷头出气,出液的畅通(进料口及进气口应用四氟生料带缠紧密封);
9.将喷头**仪器的顶部喷雾口,并旋紧固定旋钮;
10.用直径小点的蓝色PU气管连接喷头的上端及机壳右侧边上方的快速接头,连接时保证蓝色PU气管插到底;
11.用直径大点的蓝色PU气管连接喷头侧边的快速接头和右侧边上方的快速接头,连接时保证蓝色PU气管插到底;
12.插上电源线,按下绿色开关按钮(开机时,应注意红色急停处于通路状态。弹起为开,按进去为关闭),进入工作界面,点击蠕动泵按钮使蠕动泵工作。此时将医用硅胶进料管顺着蠕动泵转子的转动旋进蠕动泵,并用白色夹子固定进料管。以上工作完成后将进料管进料的一端插在喷头的进料口(以不能轻易拔下为准);
13.关闭显示屏上蠕动泵按钮使之停止转动;
14.实验时,将进料管进料的一端至于样品瓶中(实验过程中应保证样品不沉积,可在样品瓶下部用磁力搅拌达到此目的,视样品具体情况而定);
15.进入显示屏工作界面,分别点开风机、加热器、空压机、通针按钮,点击进风温度按钮设定工作所需温度并确定(设定温度时应了解溶剂沸点及溶质的熔点,温度设定值应高于溶剂的沸点并低于溶质的熔点);
16.带温度曲线趋于平稳时,点击蠕动泵工作按钮开始进料,进料速度视实验而定;
17.待试验完成后,关闭蠕动泵、空压机、通针、加热器按钮(注:此时禁止关闭风机按钮),待出风温度显示低于30度时,风机自动关闭;
18.关闭电源,断开电源线。依次取下收集瓶、冷阱、旋风分离器、玻璃干燥塔,喷头(断开蓝色PU气管时应将快速接头的蓝色部件按到底然后轻松将PU气管拔下);
19.收集好实验后的物料;
20.将玻璃部件及喷头洗净、烘干以便下次实验。
注:干燥塔、旋风分离器、冷阱、收集瓶为易碎品,安装、清洗、烘干时应轻拿轻放。
Jipad-2000ML小型喷雾干燥机产品说明:
上海旌派品牌Jipad-2000ML实验室喷雾干燥机主要适用于高校、研究所和食品医药化工企业实验室生产微量颗粒粉末,对所有溶液如乳浊液、悬浮液具有广谱适用性,适用于对热敏感性物的干燥如生物制品、生物农药、酶制剂等,因所喷出的物料只是在喷成雾状大小颗粒时才受到高温,故只是瞬间受热,能保持这些活性材料在干燥后仍维持其活性成份不受破坏。
Jipad-2000ML小型喷雾干燥机产品特征:
1、采用彩色大触摸屏操作,全自动控制和手动控制相结合,国内*:
2、全自动控制:一键式开机,设定喷雾工艺参数后,温度到达预定温度,蠕动泵自行启动,触摸屏上显示运行动画,运行流程清晰显示;关机时只需按停止键,机器自动**关机。
3、手动控制:如需在实验过程对工艺参数进行调整,可方便切换至手动状态,整个实验过程彩色触摸屏动态显示(动画)。
4、关机保护功能:关机时只需按停止键,机器除风机外立即停止运行,保证设备不会因为误操作(强行关风机)而导致加热部分烧坏。
5、喷雾、烘干及收集系统采用透明的上等高硼硅耐热玻璃材料制造,使得喷雾干燥过程在无污染及*稳定的环境下进行,且使整个喷雾干燥实验进程可直接观察,为科研人员掌控实验进程及实验结果提供了极大的便利,并能及时发现解决问题。所有玻璃元件易拆卸,易清洗。
6、内置进口全无油空压机,喷粉的颗径呈正态分布,流动性非常好,而且噪音非常低,小于60db,符合国家实验室噪音标准;
7、二流体喷雾的雾化结构,整机采用上等不锈钢材料精密制造,设计紧凑,无需附属设备,方便使用,历久如新。
8、为了满足用户在实验范围调节各项参数的要求,在干燥温度控制的设计上采用实时调控PID恒温控制技术,使全温区控温准确,加热控温精度±1℃。
9、为了保持样品的纯净,配备了进风口过滤器。
10、进料量可通过进料蠕动泵调节,*小样品量可达50ml。磁力搅拌器可选
11、干燥后的成品干粉,其颗粒度较均匀,95%以上的干粉在同一颗粒度范围。
12、小型喷雾干燥机针对黏性物料,设有喷咀清洁器(通针),在喷咀被堵塞时,会自动**,通针的频率可自动调整;
13、**的塔壁吹扫装置,物料回收率更高。
Jipad-2000ML小型喷雾干燥机技术参数:
1、喷雾干燥机全自动控制与手动控制双重控制模式,整个实验过程彩色触摸屏动态显示(动画)
2、进风温度控制:30℃~300℃
3、出风温度控制:30℃~140℃
4、蒸发水量:1500mL/H~2000ml/h
5、*进料量:蠕动泵可调*为2000ml/h
6、*小进料量:50mL
7、可升级成双级分离收集系统
8、实时调控PID恒温控制技术,加热控温精度:±1℃
9、干燥时间:1.0~1.5S
10、具有关机保护功能:关机时只需按停止键,机器除风机外立即停止运行,保证设备不会因为误操作(强行关风机)而导致加热部分烧坏。
11、彩色LCD触摸屏参数显示:进风口温度/出风口温度/蠕动泵转速/风量/通针频率
12、喷嘴口径:0.5mm/0.7mm/0.75mm/1.0mm/1.5mm/2.0mm可选,并可根据要求定制
13、设有喷咀清洁器(通针),在喷咀被堵塞时,会自动**,通针的频率可自动调整
14、喷雾干燥机整机全不锈钢制作,二流体喷雾的雾化结构,喷雾、烘干及收集系统采用透明的上等高硼硅耐热玻璃材料制造
15、内置进口全无油空压机,喷粉的颗径呈正态分布,流动性好,而且噪音非常低,符合国家实验室噪音标准;
16、整机功率:3KW/220V
17、塔壁吹扫装置,物料得率更高
18、喷雾头冷却装置(可选)
19、可直接升级成应用于有机溶剂物料干燥的氮气循环系统
20、设备尺寸:1200mm(高)×650mm(长)×500mm(宽)
Jipad-2000ML mini spray dryer installation instructions:

1 will be placed in a position close to the ventilation equipment in good position,and is fixed at the bottom of the wheel hub;

2 white PTFE gasket placed in glass drying tower along, then dry glass tower together with gasket at the top flange and put on black, finish with black kcal hoopclamp;

3 the cyclone separator jacking have red high temperature stainless steel windmark sensing, and right, and then the cyclone separator and the drying tower is connected with the medium clamp; (stainless steel sensor can move aroundregulation, convenient connection and a cyclone separator and a drying towerbetter)

The cold trap and glass drying tower is connected with a small clamp, clamping4.Jipad-2000ML spray drying;

5 small clamps a collecting bottle and cyclone separator, the clamping connection;

More than 6 before the assembly will need to dry glass tower, cyclone separator, a cold trap, a collecting bottle washing and drying;

7 the exhaust pipe connected and inserted into the symbol of the red high temperature stainless steel outlet sensing along, and ensure that the exhaust pipetail to good local ventilation, to prevent exhaust caused damage to the experimenter;

8 the nozzle clean, and drying to ensure the nozzle outlet, a liquid outlet unblocked(feeding port and an air inlet PTFE raw material belt wrapped tight sealingapplication);

9 at the top of the spray nozzle is inserted into the instrument's mouth, and tighten the fixing knob;

The 10 connecting nozzle with blue PU tracheal diameter smaller at the top and theright side of the casing side above the quick connector, connection to ensure blue PU pipe inserted in the end;

Quick connection joint nozzle side and the right side at the top of the fast joint 11with blue PU tracheal diameter larger, connection to ensure blue PU pipe inserted in the end;

12 plug the power line, press the green button switch (boot, should note the red emergency stop in the state of gateway. Bounce is open, press get off), enter the working interface, click the button to make the peristaltic pump peristaltic pumpwork. At this time the medical silicone feeding tube along the peristaltic pump rotorto rotate into the peristaltic pump, and white clip fixed feed pipe. The above work is completed in the feeding end of the tube feeding is inserted in the feed nozzlemouth (to not easily disconnect prevail);

13 close the display peristaltic pump to stop rotating button;

In 14 experiments, the feeding tube end feed for sample bottle (should ensure that the sample is not deposited, in sample bottles with the lower part of a magnetic stirring to achieve this purpose, the experimental process as the sample specific circumstances);

15 into the work of the display screen interface, respectively, point to open the fan,heater, air compressor, the needle through the button, click the button to set the temperature of inlet wind temperature and to determine the required for the job (the set temperature should be aware of the boiling point of the solvent and solutemelting point, boiling point temperature set value should be higher than the solventto solute and low melting point);

16 with temperature curves tend to be steady, the work button click peristaltic pumpstarted to feed, feed rate as the experiment set;

17 until the test is complete, close the peristaltic pump, air compressor, needle,heater button (Note: at this point the ban closed fan button), stay out of the windtemperature lower than 30 degrees, automatic closing blower;

18 power off, disconnect the power cord. Orderly collect bottles, cold trap, cyclone separator, dry glass tower, spray (disconnect blue PU pipe should be bluecomponent of rapid joint according to the end and then easily PU tracheal off);

19 collected after the experiment materials;

20 the glass components and nozzle cleaning, drying for the next experiment.

Note: the cyclone drying tower, separator, a cold trap and a collecting bottle is fragile, installation, cleaning, drying and should be handled with care.

沪公网安备 31011202007166号